![]() ![]() Cycle key 1 to OFF, then RUN, and back to OFF. Select “Ignition Key Code Erase.” Disconnect Tool and leave key in RUN for 20 seconds. Enter Security Access on the PATS control function module. Cycle key to OFF and then RUN.Ģ keys required. Enter “Ignition Key Code Erase.” Disconnect Tool and leave key in RUN for 20 seconds. Retrieve DTCs from applicable PATS control function (PATS/ICM/VIC/HEC/SCIL).ġ key required. PCM disabled the vehicle because of a PATS concern. Key program failure (defective key or transceiver).Ĭommunications issue, SCP (J1850), between PCM and PATS control (PATS/ICM/ VIC/HEC/SCIL).Ĭommunications issue, CAN (J2284), between PCM and PATS control (ICM). PCM ID does not match between the PCM and PATS control (PATS/ICM/VIC/HEC/SCIL). Non-Volatile Memory (NVM) configuration failure - No PCM ID stored in PATS. Partial detection of encoded ignition key. Unprogrammed encoded ignition key detected (leave ignition on for 20 seconds before trying a programmed key, in Anti-Scan Mode). Replace transceiver.ĮCU is defective (EEPROM in PCM is not working - replace PCM). After a valid INCODE is send to the car access to the PATS system is granted.Less than 2 (or 3 if equipped w/Valet key) keys programmed to the system. This code must be converted to a valid code (INCODE). After the diagnostic system tries to access the PATS system there will be code (OUTCODE) generated by the car. On this system ignition keys can only be programmed with a suitable Ford specific diagnostic system. On the Focus MK2 and onwards Ford uses the CODED PATS system. After the diagnostic system tries to access the PATS system there will be a time delay of about 10 minutes before access to the PATS system is granted. The TIMED PATS system protection is based on a time delay during programming of the ignition keys. If there is only 1 ignition key (or even none) the keys can only be programmed with a suitable Ford specific diagnostic system. If there are 2 Original programmed ignition keys the owner can program additional ignition keys himself. ![]() The ignition keys with blue insert are used on the old TIMED PATS system. From the Focus MK2 it is not possible anymore to program extra ignition keys yourself. On the Focus MK2 (and also the C-max) Ford used a different type of PATS chip. To programme the key itself take a look in youre manual and you will find the info you needĭoes this apply to flip out keysNo, the focus MK1 was the last focus using the ignition key with blue insert. A maximum of 4 remotes can be programmed. ![]() To program additional Remotes, repeat after 2 seconds after the sound.4. Press any button on Remote until a sound is made.3. ![]() Switch Ignition On/Off (II/0) 4 times within 6 seconds until a sound is made.2. If you wish to add a remote to the car or have more than one remote its a simple processġ. This is done buy cycling the 2 programmed keys in your ignition in turn, thus putting your car into programming mode, then you can cycle a new key in the ignition and it will be programmed to your car. Once you have both keys programmed you can then add further keys without the need for professional equipment. You must have at least 2 keys programmed for the vehicle ie the blue key and the remote fob key. The transponders in the keys have varied over the years with this system it is identified by having one key with a blue corner hence the blue key system. If you have lost your Master red key then the only way to program further keys is using professional key programming equipment to program a new master key, only then may further keys be addedįord 2 Key System (blue key system) - 1998 to current Then a further 2 keys cut for your vehicle must then be cycled in the ignition, each one being programmed in turn. Once you insert the Ford red master key, your car will enter programming mode. The purpose of the red key is to put the car into programming mode to allow further keys to be programmed to your vehicle. This system involves a red master key and 2 other user keys already programmed to the car ie ignition keys. Due to some confusion by some concerning keys and programming keys and remotes ive done this to explain the different key systems ie red keys blue keys and how it effects programming. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |